Dress-Up
Valve cover dress up kit for the Camry, Corolla and RAV4. This provides a cleaner more custom look to your engine bay.
12 short bolts go around the edge of the valve cover with the provided spacers in between and the 8 longer bolts go into the 4 coil packs and 4 spaces on top of the valve cover.
A true strut bar for the Corolla and CHR that actually works! Improve your cornering capabilities and improve steering feedback and response with this brace!
-CNC plasma cut base plates
-Steinjager billet heim joints
-1.5x.060 tubing for the lightest weight and highest strength!
-Easy 30 minute installation
-Gloss black powdercoat(blue only shown for display purposes)
-Hand tig and mig welded in the USA!
Ditch your ugly stock plastic fuel lines for these gorgeous braided lines that are E85 safe and use legit AN fittings. These lines plug right in and require no modification to the car to fit these.
These are available with black braided lines, black and red braided lines, and black and blue braided lines all from Vibrant Performance, which is the best in the industry!
Lead time is up to 2 weeks for shipping as these are made to order!
When installed please check for leaks before driving by priming the fuel system! (Turn car to key on 2-3 times w/o pressing the brake or clutch and allowing the engine to turn on) We are not responsible for damage due to improper installation
This bracket goes under your high pressure fuel pump and replaces the original steel one. By replacing the steel one you’re saving over 1 pound of weight while customizing your engines appearance, making it look much better!
Fitment:
2017 - Present 4 cylinder Camry
2019 - Present Corolla E210
2019 - Present RAV4 5th Gen
This vented oil cap kit is designed to allow you to delete the PCV valve that goes between your intake manifold and cylinder head. This valve along with the valve cover breather hose deposit a very large amount of oil and contaminants from your engines crank case into your intake tract which dirties your valves and kills performance and economy. When you delete this valve and block it’s hole off you then use the vented oil cap to route that crank case pressure to a vented or sealed oil catch can.
A vented setup would have the hose from the oil cap and the valve cover going to a catch can with a hole or filter on top to catch the oil vapor and allow the pressure to escape. With this vented setup you would seal the hole/barb that would normally go to the hose coming from the valve cover.
A sealed setup would have the oil cap and valve cover routed to a catch can and a line from the catch can back to the intake tube.
Recommended Oil Catch Can:
3 Port Catch Can (recommended to go from oil cap to catch can and valve cover breather to catch can then from the outlet to the intake)
Recommended Fittings For Oil Cap:
Plug For Hole To Use Just As Oil Cap
Recommended Hose:
10ft of 8an Braided Hose (fits the fittings on the recommended catch cans)
Fitment:
2017 - Present 4 cylinder Camry
2019 - Present Corolla E210
2019 - Present RAV4 5th Gen
Universal fitment with most Toyotas for the oil cap minus the PCV delete.
For those that take your EGR tube off of your intake to clean the nasty soot out and maintain your intakes cleanliness, this product will seal those holes up while you clean those parts so nothing goes into your intake. This is also for car shows and beauty pictures of the engine bay for dress up when not operating the vehicle. The installation and removal of the half delete takes just minutes as there is just 4 8mm bolts that hold everything together.
For the larger of the 2 pieces (half delete), you will utilize your stock gasket that comes off the OEM EGR tube.
For the full delete, the installation will be a lot more work. The performance and effects will be the same between the half and full delete as they both block the hot gasses and carbon deposits from entering the intake manifold. But the full delete will clean the engine bay up much more as far as looks go. The full delete also sheds more weight and deletes the coolant lines going through the throttle body that heats that up.
Fits:
E210 2.0 Corolla 2018+
Note:
Tuning by AMT will ensure no check engine light with this product. This tune will work hand in hand with this product to maximize the effectiveness of the product and give you more power!
AMT E210 tune
This product is for OFF ROAD USE ONLY. This product will cause a check engine light to turn on if left on the vehicle without a tune while operating due to the hot exhaust gasses not going into your intake system.
This is the first and only true catch can system designed specifically for the E210 Corolla!
The PCV (positive crankcase ventilation) system on these cars has a one way valve between the intake manifold and cylinder head that uses vacuum from the intake manifold to pull pressure from the engine crank case into the intake system which helps with efficiency of the engine. The problem is that along with the pressure its relieving its bringing a lot of oil vapor into the intake manifold as well. If you take the hose from the valve cover to the intake tube off its going to be bone dry 99% of the time and the generic catch can systems that just put the can between the valve cover and the intake hose will never see a drop of oil. Yet when you take the intake manifold off you will see oil dripping out of the intake runners and coating the inside of the cylinder head. 99% of the nasty crap from the PCV system on these cars comes from that valve between the intake manifold and cylinder head.
But we made a proper solution! Most catch can systems on all other cars put the can between the PCV valve and the intake manifold to catch this oil vapor, but unfortunately with the way this PCV system was designed you can’t do that. So what we did was design a plug to put in place of the PCV valve which completely blocks that, and instead reroute the crankcase pressure out of the custom vented oil cap we designed. Both the oil cap and the valve cover breather route to the catch can and then the can routes back to the intake tube so the vacuum from that pulls the pressure out of the crankcase without the oil coming with it and gumming everything up.
In addition to this being the only catch can system on the market to address the issue, we put the can in an out of the way spot that allows you to easily drain the can. We mounted the catch can right behind the front bumper under the driver side headlight. With this location you can drain the can by undoing the 3 10mm bolts holding the front flap of the inner fender liner, pulling that flap back and simply twisting the valve open. No need to take the can out of the car every time you need to drain it and it is right down there with you every time you change your oil so you can drain it into the same spot as your old used oil.
When making this catch can system we went with the best materials we could find as we are all about quality and fit and finish. We understand that not everyone needs the best materials and may simply want a product that works. With that being said, we made 2 versions! They’re exactly the same as far as functionality goes. One is just made with rubber hose and push on fittings and the other is made with Vibrant Performance high quality braided lines with high end reusable hose end fittings. If you’re looking for that extra flair to your engine bay at shows or car meets or even just for you to look at then the braided lines are definitely the way to go. If you just want to keep that oil where it belongs and not in your intake manifold then the rubber hose will definitely be more than sufficient for what you need.
These are made to order and have a 2-4 week lead time. We strive to get these made and sent out asap though and will always do what we can to get these shipped out in a timely manner.
Ever look at the rear of your Corolla Hatch and think the rear was just off a bit? Wasn’t as symmetric as you’d like? Easy fix! Delete the rear wiper! Makes a huge improvement in looks, and in addition to that you save another 2lbs in weight. And with these cars, every ounce really does count.
These are designed to fit the Corolla Hatch perfectly. The 2 billet aluminum pieces are both o-ringed for a perfect seal, anodized with UV resistant dye and they were also machined so you could tighten the bolt that joins them together all the way down and not have to risk cracking your window or having to do it multiple times due to misalignment with a part that wasn’t designed for this car.
This easy modification can be installed in just minutes with ease! No need to take it to a shop or pay a friend to do it.
For hatchback model only, sedan does not have a rear wiper to delete
These Pods directly replace your driver side defrost vent so you can install a 52mm gauge to monitor anything from oil temp to boost pressure if you add a turbo! No cutting or drilling needed for the installation of this product, so it is completely reversible.
A highly recommended gauge that requires no wiring and plugs right into the OBD2 port and shows any parameters the car can see is this gauge here!
Give your E210/GR Corolla hatch or sedan the ultimate look with this tube steel front crash bar! This bash bar opens up the front of your car and allows for more airflow, mounting of accessories like lights and horns as well as show winning looks!
-Made of strong DOM tube steel. This is the same stuff we build roll cages out of!
-Improved cooling
-Show winning looks
-Hand welded in house here in the USA